Skip to main content

How to do VW Jetta 2012 with vvdi2

Question: Can I do vw Jetta 2012
Push to start ?
If yes what Is the process please?
I have vvdi2 and prog


Tip 1: Have the right key first then go into service mode and make dealer key , after that learn all keyless go to the car putting the new numbers of keys count and interacting them to the coil below steering wheel gl

Tip 2: If it’s not all keys lost you can do all obd. If akl service mode and you’ll have to short a fuse to get ignition on. But as said above make sure you have the right key first

Source: 

VW Jetta 2012 – vvdi2 and vvdi prog

Comments

Post a Comment

Popular posts from this blog

vvdi2 full configuration detail function list

Question:  I have the vvdi2 device with the basic one. How much will it cost me to open it to the full package? Answer:  i advise you to sell you vvdi 2 device with the basic one (sv86-c) since it's  2500 usd  for full configuration  but if you get a new  vvdi2 full configuration , it's  1700 usd that is it's 1700 usd for vvdi2 device + full configuration: 1)  VV-01 VAG 4th immobilizer :  activated! 2)  VV-02 VAG Audi 5th immobilizer :  activated! 3)  VV-03 VAG copy 48 transponder  by OBDII:  activated! 4)  VV-04 Copy 48 96 bit :  activated! 5) VV-05 VAG MQB immobilizer:  activated! 6)  VB-01 BMW OBD :  activated! 7)  VB-02 BMW CAS4 :  activated! 8)  VB-03 BMW FEM/BDC :  activated! 9) VP-01 Porsche immo data tool:  activated! 10) VPSA-01 PSA:  activated! 11) VK-01 Transponder Programmer:  activated! 12) VJ-01 Passthru J2534:...
Post a Comment
Read more

Good to Know VVDI2 PassThru J2534

Confirmed!  VVDI 2 J2534  work with pass-thru Ford, and even avdi work also. I test the two For the SAE J2534 pass-thru device being used, select the device manufacturer and follow the list below Correct the selected pass-thru device to the PC Select "Save device" Select "Exit application" Restart module programming Note: If no devices are listed below, the software that was received with the pass-thru device was not installed. Exit the app, install the software and restart module programming Good to know:  VVDI2 PassThru J2534 Configuration software supports Third–Party software to connect to VVDI2 for communication. Third Party software should support SAE J2534 function. And now it supports VAG diagnostics software: OIDS, VAS5054 and others. You can find detail in VVDI2 – PassThru J2534 User Manual. PassThru J2534 is available in both VVDI2 basic and full function version. VVDI2 Version VVDI2 full function VVDI2 Basic version Price 2499 usd 46...
Post a Comment
Read more

VVDI2 VAG 4th 5th immo key programming

VVDI2 VAG mainly supports Diagnostic, 4th immobilizer, 5th immobilizer, key learn, BCM remote control, Engine control unit, Kline instrument and immobox, adapt unit, component protection, dump tool etc for VW, Audi, Seat, Skoda. VVDI 2 VAG also support 4th immobilizer Porsche, 4th immobilizer Bentley. Here are  Xhorse VVDI2 VAG Commander function list and car list. ALL functions below can be realized with VVDI2 full kit  or  VVDI2 VAG VVDI II VAG Commander Diagnostic: Support TP2.0, UDS, KWP1281, KWP2000 protocol, have internal database, can display every item in detail Identification: read the detail information for target unit Coding: Set unit coding Actuator test: Test every small actuator in target unit Read DTCs: Read trouble codes Clear DTCs: Clear trouble codes Basic settings: Complete basic settings for target unit Security access: Login with PIN code, usually use before adaptation Adaptation: Set new value in channel Custom requests: You can wr...
Post a Comment
Read more